Radiant Floor and Tubing Accessories

Heat Transfer Plate

Extruded Aluminum Heat Transfer Plates - For use in radiant floor heating via joist space applications (under sub-floor) with 3/8" or 1/2" PEX tubing. Plates are 3-1/2" x 4' long and pre-drilled for wood screws to attach underneath sub-floor. PEX tubing is held securely in tube channel on under side of plate.

Mounting Rail

Tube Mounting Rail- Used to hold tubing to rigid foam, wood or concrete. Mounting holes are provided for appropriate fasteners. 6-1/2" (78") rails have prescored "break" lines should shorter lengths be needed. Holding slots are spaced every 2"

Ratchet Tube Cutter

The Legend high quality and durable plastic ratchet tube cutter can be used to cut CPVC and PVC tubing. Includes a replacement blade. The ratchet tube cutter can cut CPVC and PVC up to 1-1/4" in diameter.

Standard Tube Clamps

Plastic tube fastener for securing flexible plastic tube to solid surfaces, floor joists and wall studs. Protects and keeps tubing straight when routing in plumbing and hydronic piping. includes two pre-drilled screw holes, fits CTS 1/2", 3/4" and 1".

Tube Isolation Clamps

Plastic tube fastener for isolating flexible plastic tube as it passes through building floor joists and wall studs. Protects tubing from sharp or hard surfaces, ideal for plumbing and hydronic piping. Includes two pre-drilled screw holes, fits CTS 1/2", 3/4" and 1".

Tube Bend Support

Holds tube in a tight radius 90° bend without a fitting elbow and without fear of "kinking." Slide support easily around 1/2" tube while straight, then make bend by clicking tabs together.

Tube Bend Support, Metal

Metal bend support for 1/2", 3/4" and 1" flexible plastic tubing."

Tube Bend Support, Plastic

Bend support made from durable plastic with nail tab for securing to studs or joists when routing plastic tubing in plumbing installations. For 1/2", 3/4" and 1" tubing.

Tube Cutter

The Legend high quality and durable plastic tube cutter can be used to cut PEX, CPVC and PVC tubing. Include a replacement blade. The tube cutter can cut PEX up to 2" in diameter.

Tube Holding Pins

Designed to be manually inserted into QuickTherm™ "knobs" to hold down large diameter tube (typ. 3/4") in tough spots where additional support may be needed. Works on all sizes of tube and all models (thicknesses) of QuickTherm.

Tube Protection Sleeve

Used to protect tubing in a concrete slab at expansion joints. Pre-slit 12" lengths allow for rapid installation after tubing has been installed and before concrete pour.

Tube Repair

Repair Adapter for 5/16" to 3/4" Manifold Connectors for PEX Tubing and Repair Yellow Silicone Tape

Tube Talon Fasteners

Plastic Talon hook with nail included, secures tubing to wooden surfaces. Ideal for neatly routing and attaching flexible plastic tubing to floor joists and wall studs. For CTS 1/2", 3/4".

Tube Track

Tube Track & Tube Track Duo Used to hold tubing to rigid foam, wood or concrete. Mounting holes are provided for appropriate fasteners. Clips at end of each piece allow 3-1/4" (39") sections to snap together. Use tube holding pins (top) in rigid foam board installations.

ST-100 Up-Right Tube Installation Tool

The ST-100 Up-right hand staple tool is for installing radiant tube in concrete slab applications. The long handle allows the installer to easily staple down flexible radiant tube to rigid foam insulation while walking. The tool is easy to operate and will reduce installers fatigue while lowering the time to install. Extruded polystyrene insulation board is recommended to be used under concrete slabs.

The staples are available in three sizes and selected based on the diameter of the tube, 3/8", 1/2", 5/8" and 3/4". The staples come in magazines of 30, (the 1-1/2" long staple is in 25.) The magazines load easily into the tool and are fed via gravity with a metal weight. This new design is simple and virtually eliminates staple jams.